SHURE MXWANI4

SHURE MXWANI4

Audio Network Interface
Audio network interface streamlines Microflex Wireless connectivity to conference room AV systems over 4 channels to enable easy system set-up. Features include corporate uplink mode and Dante networking to transport low-latency digital audio. 
Brand:
Product Code:MXWANI4-E
FEATURES
  • Analog connections: 4 or 8 block connector channel outputs, with 1 or 2 block connector inputs (model dependent)
  • Four port gigabit switch: Optimized port configurations for connection to the Access Point Transceiver and Networked Charging Stations, third party control systems, and corporate networks 
  • Ethernet connectivity: Send audio and control signals over long cable runs of up to 300 feet or anywhere over a corporate network
  • Power over Ethernet: Port 1 of the rear panel switch supplies power over Ethernet to the Access Point Transceiver for simplified installation
  • Corporate uplink mode: Link to the corporate network for remote control of system settings while keeping audio off the network for security and to reduce bandwidth
  • Front panel controls: Mute or solo channels and set input/output levels easily from the front panel
  • PC/Mac software control: Access the Microflex Wireless Control Software from a networked computer for input/output levels and port configuration 
  • Dante™ networking: Transports low latency digital audio received from wireless microphones over Ethernet to any other Dante-equipped device
  • Headphone output: Solo audio signal on any channel
  • Audio Frequency Response: 20 Hz to 20 kHz (+1, −1.5 dB)
  • Dynamic Range (20 Hz to 20 kHz, A-weighted, typical): Analog-to-Dante: 113 dB; Dante-to-Analog: 110 dB
  • Output Noise (20 Hz to 20 kHz, A-Weighted, typical): Line: −84.5 dBV; Aux: −95.2 dBV; Mic: −106.5 dBV
  • THD+N (20 Hz to 20 kHz@ +4dBu analog input, −10 dBFS digital input): <0.05%
  • Polarity: Non-inverting, any input to any output
  • Dimensions: 44 mm × 483 mm × 366 mm (1.7 in. × 19.0 in. × 14.4 in.), H × W × D
  • Weight: 3.1 kg (6.9 lbs)
  • Housing: Steel; Extruded aluminum
  • Power Requirements: 100 to 240 V AC, 50–60 Hz, 1 A
  • Operating Temperature Range: −18°C (0°F) to 63°C (145°F)
  • Storage Temperature Range: −29°C (-20°F) to 74°C (165°F)

ANALOG CONNECTIONS - OUTPUTS
  • Configuration: Active Balanced
  • Impedance: 310 Ω
  • Clipping Level (minimum): Line: +26.2 dBV; Aux: +16.2 dBV; Mic: −3.8 dBV

ANALOG CONNECTIONS - INPUT(S)
  • Configuration: Active Balanced
  • Impedance: 10.6 kΩ
  • Clipping Level (minimum): Line: +23.8 dBV; Aux: +10.8 dBV
  • Headphone Output:
- 6.35 mm (1/4"): TRS, 100 mW, 350 Ω, dual mono (will drive stereo phones)
- 0 dBV=1 V RMS 0 dBu=0.775 V RMS 0 dBV=2.2 dBu

DIGITAL SIGNAL PROCESSING
  • AD/DA Converter: 24-bit, 48 kHz
  • Latency (Estimated Nominal, ±0.1 ms): Analog-to-Dante: 0.21 ms; Dante-to-Analog: 0.24 ms + TN
TN = Network latency in milliseconds, as set in Dante Controller.
Note: Dante network latency is typically associated with the receiving device.

NETWORKING
  • Network Interface: Four-Port Gigabit Ethernet Switch, Dante digital audio
  • Uplink Port (Port 4): Selectable, blocks multicast traffic
  • Power over Ethernet (PoE): Provided on Port 1 to power MXWAPT
  • Cable Requirements: Cat 5e or higher, shielded, 100 m maximum between network devices
  • Network Addressing Capability: DHCP, link-local, static