FEATURES
- Analog connections: 4 or 8 block connector channel outputs, with 1 or 2 block connector inputs (model dependent)
- Four port gigabit switch: Optimized port configurations for connection to the Access Point Transceiver and Networked Charging Stations, third party control systems, and corporate networks
- Ethernet connectivity: Send audio and control signals over long cable runs of up to 300 feet or anywhere over a corporate network
- Power over Ethernet: Port 1 of the rear panel switch supplies power over Ethernet to the Access Point Transceiver for simplified installation
- Corporate uplink mode: Link to the corporate network for remote control of system settings while keeping audio off the network for security and to reduce bandwidth
- Front panel controls: Mute or solo channels and set input/output levels easily from the front panel
- PC/Mac software control: Access the Microflex Wireless Control Software from a networked computer for input/output levels and port configuration
- Dante™ networking: Transports low latency digital audio received from wireless microphones over Ethernet to any other Dante-equipped device
- Headphone output: Solo audio signal on any channel
Audio Frequency Response: 20 Hz to 20 kHz (+1, −1.5 dB)
Dynamic Range (20 Hz to 20 kHz, A-weighted, typical): Analog-to-Dante: 113 dB; Dante-to-Analog: 110 dB
Output Noise (20 Hz to 20 kHz, A-Weighted, typical): Line: −84.5 dBV; Aux: −95.2 dBV; Mic: −106.5 dBV
THD+N (20 Hz to 20 kHz@ +4dBu analog input, −10 dBFS digital input): <0.05%
Polarity: Non-inverting, any input to any output
Dimensions: 44 mm × 483 mm × 366 mm (1.7 in. × 19.0 in. × 14.4 in.), H × W × D
Weight: 3.2 kg (7.1 lbs)
Housing: Steel; Extruded aluminum
Power Requirements: 100 to 240 V AC, 50–60 Hz, 1 A
Operating Temperature Range: −18°C (0°F) to 63°C (145°F)
Storage Temperature Range: −29°C (-20°F) to 74°C (165°F)
ANALOG CONNECTIONS - OUTPUTS
Configuration: Active Balanced
Impedance: 310 Ω
Clipping Level (minimum): Line: +26.2 dBV; Aux: +16.2 dBV; Mic: −3.8 dBV
ANALOG CONNECTIONS - INPUT(S)
Configuration: Active Balanced
Impedance: 10.6 kΩ
Clipping Level (minimum): Line: +23.8 dBV; Aux: +10.8 dBV
Headphone Output: 6.35 mm (1/4") TRS, 100 mW, 350 Ω, dual mono (will drive stereo phones); 0 dBV=1 V RMS 0 dBu=0.775 V RMS 0 dBV=2.2 dBu
DIGITAL SIGNAL PROCESSING
AD/DA Converter: 24-bit, 48 kHz
Latency (Estimated Nominal, ±0.1 ms): Analog-to-Dante: 0.21 ms; Dante-to-Analog: 0.24 ms + TN
(TN = Network latency in milliseconds, as set in Dante Controller. Note: Dante network latency is typically associated with the receiving device.)
NETWORKING
Network Interface: Four-Port Gigabit Ethernet Switch, Dante digital audio
Uplink Port (Port 4): Selectable, blocks multicast traffic
Power over Ethernet (PoE): Provided on Port 1 to power MXWAPT
Cable Requirements: Cat 5e or higher, shielded, 100 m maximum between network devices
Network Addressing Capability: DHCP, link-local, static
